vo3052, VO3053 www.vishay.com vishay semiconductors rev. 1.9, 11-aug-11 1 document number: 83749 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, phototriac output, 1.5 kv/s dv/dt, 600 v description the vo3052 and VO3053 triac driver family consists of a gaas infrared led optically coupled to a monolithic photosensitive non zero crossing triac detector chip. the 600 v blocking voltage permits control of off-line voltages up to 240 v ac , with a safety factor or more than two, and is sufficient for as much as 380 v. features ? 1500 v/s dv/dt minimum 2000 v/s typical ? 600 v blocking voltage ? 100 ma on-state current ? low input trigger current ? 6 pin dip package ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec applications ? household appliances ? triac drive/ac motor drives ? solenoid/valve controls ? office automation equipment/machine ? temperature (hvac)/lighting controls ? switching power supply agency approvals ? ul-file e52744 system code h or j ? cul - file no. e52744, equivalent to csa bulletin 5a ? din en 60747-5-2 (vde 0884) available with option 1 i179041-3 1 2 3 6 5 4 mt2 mt1 nc a c nc v de i179041-2 dip s md ordering information vo305#-x0##t part number package option tape and reel agency certified/pack age trigger, current i ft (ma) ul, cul 5 10 dip-6 VO3053 vo3052 dip-6, 400 mil, option 6 VO3053-x006 vo3052-x006 smd-6, option 7 VO3053-x007t vo3052-x007t smd-6, option 9 VO3053-x009t - vde, ul, cul 5 10 dip-6, 400 mil, option 6 - vo3052-x016 > 0.1 mm 10.16 mm > 0.7 mm 7.62 mm dip option 7 option 6 option 9
vo3052, VO3053 www.vishay.com vishay semiconductors rev. 1.9, 11-aug-11 2 document number: 83749 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mount ed devices (smd). refer to wave profile for soldering conditi ons for through hole devices (dip). note ? the thermal model is repr esented in the thermal network below. each resistance value given in this model can be used to calcul ate the temperatures at each node for a given operating condition. the th ermal resistance from board to ambient will be dependent on th e type of pcb, layout and thickness of copper traces. for a detailed explan ation of the thermal model, please reference vishays thermal characteristics of optocouplers application note. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition part symbol value unit input reverse voltage v r 6v forward current - continuous i f 60 ma power dissipation p diss 100 mw output off state output terminal voltage vo3052, VO3053 v drm 600 v peak repetitive surge cu rrent pw = 100 ms, 120 pps i tsm 1a power dissipation p diss 200 mw on-state rms current i t(rms) 100 ma coupler isolation test voltage t = 1 s v iso 5300 v rms total power dissipation p tot 300 mw operating temperature t amb - 40 to + 100 c storage temperature t stg - 55 to + 150 c soldering temperature (1) 10 s t sld 260 c thermal characteristics parameter symbol value unit maximum led junction temperature t jmax. 125 c maximum output die junction temperature t jmax. 125 c thermal resistance, junction emitter to board ? jeb 150 c/w thermal resistance, junction emitter to case ? jec 139 c/w thermal resistance, junction detector to board ? jdb 78 c/w thermal resistance, junction detector to case ? jdc 103 c/w thermal resistance, junction emitter to junction detector ? jed 496 c/w thermal resistance, case to ambient ? ca 3563 c/w t a ca t c t jd t je t b ec eb dc db ba de t a 19996 package
vo3052, VO3053 www.vishay.com vishay semiconductors rev. 1.9, 11-aug-11 3 document number: 83749 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? typical values are characteristics of the device and are the re sult of engineering evaluations. typical values are for informa tion only and are not part of the te sting requirements. note ? as per iec60747-5-5, 7.4.3.8.1, this optocoup ler is suitable for safe electric al insulation only with in the safety ratings. compliance with the safety ratings shall be ensured by means of prodective circuits. electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit input reverse current v r = 6 v i r 10 a forward voltage i f = 30 ma v f 1.2 1.5 v output leakage with led off, either direction v drm = 600 v i drm 10 500 na critical rate of rise off-state voltage v d = 400 v dv/dt cr 1500 2000 v/s coupler led trigger current, current required to latch output VO3053 i ft 5ma vo3052 i ft 10 ma peak on-state voltage, either direction i tm = 100 ma peak, i f = rated i ft v tm 1.7 3 v holding current, either direction i h 200 a coupling capitance 10 khz c io 0.4 pf safety and insulation ratings parameter test condition symbol min. typ. max. unit climatic classification iec68 part 1 40/100/2 1 pollution degree din vde 0109 2 tracking resistance (comparative tracking index) insulation group illa cti 175 highest allowable overvoltage transient overvoltage v iotm 8000 v peak maximum working insulation voltage recurring peak voltage v iorm 890 v peak insulation resistance at 25 c v io = 500 v r is ? 10 12 ? insulation resistance at t s v io = 500 v r is ? 10 12 ? insulation resistance at 100 c v io = 500 v r is ? 10 12 ? partial discharge test voltage method a, v pd = v iorm x 1.875 v pd 1669 v peak safety limiting values - maximum values allowed in the event of a failure output power p so 500 mw input current i si 250 ma case temperature t si 175 c minimum external air gap (clearance) measured from input terminals to output terminals, shortest distance through air ??? mm minimum external tracking (creepage) measured from input terminals to output terminals, shortest distance path along body ??? mm minimum external air gap (clearance) measured from input terminals to output terminals, shortest distance through air ??? mm minimum external tracking (creepage) measured from input terminals to output terminals, shortest distance path along body ??? mm
vo3052, VO3053 www.vishay.com vishay semiconductors rev. 1.9, 11-aug-11 4 document number: 83749 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - forward voltage vs. forward current fig. 2 - off-state leakage current vs. temperature fig. 3 - on-state current vs. v tm fig. 4 - normalized trigger current vs. temperature fig. 5 - turn-on time vs. led current fig. 6 - normalized holding current vs. temperature 0.5 0.7 0.9 1.1 1.3 1.5 110100 forward led current (ma) forward led voltage (v) - 40 c 85 c 25 c 20335 1 10 100 1000 - 40 - 20 0 20 40 60 80 100 temperature (c) i ikg (na) 20337 - 100 - 80 - 60 - 40 - 20 0 20 40 60 80 100 - 2 - 1.5 - 1 - 0.5 0 0.5 1 1.5 2 on-state voltage v tm (v) on-state current i tm (ma) 20338 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 - 40 10 60 temperature (c) normalized i ft 20340 100 1 10 100 579111315 led current (ma) turn-on time (s) 20341 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 - 40 - 20 0 20 40 60 80 100 temperature (c) normalized i h 20342
vo3052, VO3053 www.vishay.com vishay semiconductors rev. 1.9, 11-aug-11 5 document number: 83749 for technical questions, contact: optocoupleranswers@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 7 - turn-on time vs. temperature fig. 8 - trigger current vs. pulse width package dimensions in millimeters package marking notes ? the vde logo is only marked on option1 parts. ? tape and reel suffix (t) is not part of the package marking. 0 5 10 15 20 25 - 40 - 20 0 20 40 60 80 100 temperature (c) turn-on time (s) 20339 4.0 4.2 4.4 4.6 4.8 5.0 30 45 60 75 90 pulse width (s) i ft (ma) 20343 100 i178014_1 0.2 0.3 3.3 3.81 3.3 3.81 0.84 typ. 7.62 typ. 0.84 typ. 2.54 typ. 1 min. 0.46 0.51 1.22 1.32 6.3 6.5 8.5 8.7 pin one id 6 5 4 1 2 3 18 3 - 9 7.62 to 8.81 4 typ . iso method a 0.35 0.25 10.16 10.92 7.8 7.4 10.36 9.96 20 8 min. 7.62 typ. 4.6 4.1 8.4 min. 10.3 max. 0.7 option 7 option 6 v yww h 68 vo3052
legal disclaimer notice www.vishay.com vishay revision: 12-mar-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products no t expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale , including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding th e design or manufacture of the part. please contact authorized vishay personnel t o obtain written terms and conditions regardin g products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu.
|
